StriCoreHerbicide

Under which condition is an applicator prohibited from applying StriCore?

• When wind speeds exceed 15 mph. ✓
• When applying to turfgrass in residential areas.
• When using surfactants that have been tested for compatibility.
• When applying to seeded or sodded turfgrass.

Answer: Do not apply when wind speeds exceed 15 mph.

🔗 Source

According to the label, which of the following is a requirement for Personal Protective Equipment (PPE) for all handlers?

• Chemical-resistant apron and boots.
• Long-sleeved shirt, long pants, shoes plus socks, protective eyewear, and waterproof gloves. ✓
• N95 respirator, long sleeves, and chemical-resistant gloves.
• Long-sleeved shirt, long pants, chemical-resistant boots, and a face shield.

Answer: PPE: Long-sleeved shirt and long pants, shoes plus socks, protective eyewear, and waterproof gloves are required for applicators and all other handlers.

🔗 Source

Under which weather condition should an applicator avoid applying StriCore due to the risk of droplet evaporation?

• High wind speeds exceeding 15 mph
• Low relative humidity ✓
• Temperature inversions
• Conditions favoring wind erosion of soil

Answer: The timing and weather section states: 'Avoid application in low relative humidity to prevent droplet evaporation.'

🔗 Source

What is the required procedure for mixing StriCore with water?

• Fill the tank with water, then add StriCore and agitate.
• Mix with one fourth of the volume of clean water needed for the area to be treated, starting agitation before adding StriCore. ✓
• Mix with full volume of water and agitate until the product is dissolved.
• Dilute StriCore with surfactants to ensure even mixing.

Answer: The mixing instructions state: 'Mix with one fourth of the volume of clean water needed for the area to be treated. Start agitation and add StriCore to the tank.'

🔗 Source

According to the mixing instructions, what should be done immediately after adding StriCore to the tank and mixing thoroughly?

• Begin spraying the target area immediately.
• Add another product to the tank.
• Fill the tank to capacity and operate the sprayer for 15 minutes to flush equipment. ✓
• Wait 12 hours before operating the sprayer.

Answer: Fill the tank to capacity and operate the sprayer for 15 minutes to flush hoses, boom, and nozzles.

🔗 Source

What is the required Personal Protective Equipment (PPE) for handling StriCore?

• Long-sleeved shirt, long pants, shoes, protective eyewear, and waterproof gloves ✓
• Long-sleeved shirt, long pants, boots, and chemical-resistant apron
• N95 mask, gloves, eyewear, and long-sleeved shirt
• Long pants, shoes, and waterproof gloves

Answer: The PPE section lists: 'long-sleeved shirt, long pants, shoes, protective eyewear, and waterproof gloves'.

🔗 Source

According to the product description, what is the maximum annual application rate of StriCore per acre?

• 1.5 lb a/i/acre ✓
• 4 lbs of Pethoxamid per gallon
• 48 fl oz per acre
• 15 fl oz per acre

Answer: The label states: 'Do not apply more than 48 fl oz of StriCore per acre (1.5 lb a/i/acre) per year.'

🔗 Source

When mixing StriCore, what is the correct procedure for filling the spray tank?

• Fill the tank to capacity, then add StriCore and water.
• Fill the spray tank one-fourth full with clean water, add StriCore, and then fill to capacity. ✓
• Fill the tank one-half full with water, add StriCore, and then fill to capacity.
• Fill the tank one-quarter full with StriCore and then add water.

Answer: Fill spray tank one-fourth full with the water of clean water needed for the area to be treated. Start the agitation system and add StriCore to the tank. Fill the tank to capacity...

🔗 Source