Sanidate 5 0

When performing direct disinfection of membranes, what are the required pH and temperature conditions?

• pH range of 3-7 and maximum water temperature of 80 degrees F ✓
• pH range of 1-14 and maximum water temperature of 100 degrees F
• pH range of 5-8 and maximum water temperature of 75 degrees F
• pH range of 3-7 and minimum water temperature of 80 degrees F

Answer: The label requires direct disinfection of membranes to be within a pH range of 3-7 and a maximum water temperature of 80 degrees F.

🔗 Source

What is the application rate for fogging to control non-public health microorganisms on hard, non-porous surfaces?

• 1 fl. oz. per gallon
• 2.5 fl. oz. per gallon
• 1 quart per 1,000 feet of room area ✓
• 0.85-1.27 fl. oz. per 100 gallons

Answer: Under the mixing notes for fogging non-public health microorganisms, it specifies 1 quart per 1,000 feet of room area.

🔗 Source

What is the correct dilution rate for a rapid cleaning application in watering systems?

• 1:128 dilution
• 1:50 (2% solution) dilution ✓
• 1:80 dilution
• 1:100 dilution

Answer: For rapid cleaning applications in watering systems, the label specifies a 2% solution (1:50) at a rate of 2.5 fl. oz. per gallon.

🔗 Source

According to the mixing instructions for a standard medicator stock solution, what is a critical restriction?

• Do not mix SaniDate 5.0 with other product in the same stock solution ✓
• Do not use SaniDate 5.0 in water temperatures above 70 degrees F
• Do not apply the stock solution to non-porous surfaces
• Do not use a metering pump for stock solutions

Answer: The restrictions state: 'Do not mix SaniDate 5.0 with other product in the same stock solution.'

🔗 Source

What is the target pest for SaniDate 5.0 when applied to drinking water and watering lines in livestock operating systems?

• Non-public health microorganisms that cause decay and spoilage
• Bacteria ✓
• Microorganisms that cause decay in food packaging
• Pests that damage metal grating and structural steel

Answer: The label specifies that for drinking water and watering lines, the target pest is bacteria.

🔗 Source

When using SaniDate 5.0 for fogging to control non-public health microorganisms, what is the required re-entry interval for personnel?

• Vacate the room during fogging and for a minimum of 1 hour after fogging ✓
• Vacate the room for a minimum of 3 to 6 hours after fogging
• Vacate the room for a minimum of 10 minutes after fogging
• Vacate the room for a minimum of 1 hour before fogging begins

Answer: The label states to vacate all personnel from the room during fogging and for a minimum of 1 hour after fogging.

🔗 Source

For a Clean in Place (CIP) application involving filters, how long must the solution be re-circulated?

• A minimum of 10 minutes ✓
• A minimum of 1 hour
• 3 to 6 hours
• At least 10 minutes per 1,000 feet

Answer: For CIP applications involving filters, the label states to re-circulate the solution for a minimum of 10 minutes.

🔗 Source

When applying SaniDate 5.0 as a foam treatment for cleaning hard, non-porous surfaces, what must be done to food contact surfaces before re-use?

• They must be rinsed with potable water ✓
• They must be dried with a waterproof covering
• They must be fogged for 1 hour
• They must be treated with an alkaline detergent

Answer: The label notes for foaming applications that any food contact surfaces must be rinsed with potable water prior to re-use.

🔗 Source