Bio-Tam 2.0

Under what soil temperature conditions should Bio-Tam 2.0 be applied?

• When soil temperature is at least 32°F (0°C)
• When soil temperature is at least 50°F (10°C) ✓
• When soil temperature is at least 60°F (15°C)
• Only when soil is saturated

Answer: Apply Bio-Tam 2.0 when the soil temperature is at least 50°F (10°C).

🔗 Source

If the soil is dry when applying the product, what action must the applicator take?

• Pre-irrigate until moist, or irrigate again immediately after application ✓
• Wait for rain to moisten the soil
• Apply only in the evening to prevent evaporation
• Mix the product with extra water to increase moisture

Answer: If soil is dry, pre-irrigate until moist. If applied to dry soil, irrigate again immediately after application.

🔗 Source

Which of the following is a restriction regarding application sites for Bio-Tam 2.0?

• Do not apply to root systems of susceptible crops
• Do not apply to areas where water surface is present or to intertidal areas below the mean high water mark ✓
• Do not apply to crops in the collar region
• Do not apply to any outdoor areas

Answer: Do not apply to areas where water surface is present or to intertidal areas below the mean high water mark.

🔗 Source

What is the required order of addition when mixing Bio-Tam 2.0 in a tank with other pesticides?

• Liquids, then aqueous suspensions, then wettable powders, then dry flowables
• Dry flowables, then wettable powders, then aqueous suspensions, then flowables, then liquids ✓
• Water, then surfactants, then liquids, then dry flowables
• Dry flowables, then liquids, then aqueous suspensions, then wettable powders

Answer: When mixing in a tank, follow the order of mixing: fill tank with at least one-half full of water and begin agitation; add dry flowables (DF), then wettable powders (WP), aqueous suspensions (AS), flowables (F), and liquids (L).

🔗 Source

When is it prohibited to use Bio-Tam 2.0 in the state of Texas?

• In any area where water surface is present
• In areas where endangered beetles are found, specifically in Red River and Lamar counties ✓
• In any area with a soil temperature below 50°F
• In any county where irrigation is used

Answer: Do not use in areas where endangered beetles are found (specifically in Texas - Red River, Lamar...)

🔗 Source

How should an applicator prepare a suspension using Bio-Tam 2.0?

• Combine 1 pound of product for every 1 gallon of water
• Combine 1.25 pounds of product for every 1 pound of water
• Combine 1 pound of product for every 1.25 gallons of water and mix from time to time ✓
• Dilute 1 pound of product in 2 gallons of water

Answer: To prepare a suspension, combine 1 pound of this product for every 1.25 gallons of water, and mix from time to time in order to promote the germination of conidia and obtain faster soil colonization.

🔗 Source

What is the restricted-entry interval (REI) for this product?

• 24 hours
• 12 hours
• 4 hours ✓
• 48 hours

Answer: REI: 4 hours

🔗 Source

Which personal protective equipment (PPE) is specifically required for mixers/loaders and applicators when handling this product?

• Waterproof gloves and long-sleeved shirt
• Shoes and socks
• A dust/mist filtering respirator meeting NIOSH standards of at least N-95, R-95, or P-95 ✓
• A chemical-resistant apron and face shield

Answer: mixers/loaders and applicators must wear a dust/mist filtering respirator meeting the NIOSH standards of at least N-95, R-95, or P-95.

🔗 Source