Bifen I T

To achieve a 0.12% finished strength, how much product should be mixed with 49.75 gallons of water?

• 1 qt. ✓
• 2 qt.
• 0.5 qt.
• 1.5 qt.

Answer: The mixing instructions state that 1 qt. of product in 49.75 gallons of water results in a 0.12% finished strength.

🔗 Source

When treating for termites in soil, the label notes that the 0.06% rate should only be used in conjunction with what?

• Pre-construction applications
• Injection techniques
• Volume adjustments, foam applications, or underground services applications ✓
• A minimum of 2 quarts of product per 100 gallons

Answer: The notes for soil termite treatment state to use that rate only in conjunction with volume adjustments, foam applications or underground services applications.

🔗 Source

What is the required dilution concentration for pre- and postconstruction applications against subterranean termites?

• 0.06%
• 0.32%
• 0.12% ✓
• 1.0%

Answer: The label specifies a 0.12% dilution for pre- and postconstruction applications.

🔗 Source

When treating soil for subterranean termites, what is the required application rate for a 0.06% dilution?

• 4 gallons of dilute dilution per 10 linear feet per foot of depth of the trench, or 1 gallon per 1.0 cubic feet of soil ✓
• 0.5 gallons per 10 ft2 (horizontal) or 2.0 gallons per 10 linear ft. (vertical)
• 1 quart per 99.75 gallons of water
• 3.2 oz. per 4.975 gallons of water

Answer: The label specifies 4 gallons of dilute dilution per 10 linear feet per foot of depth of the trench, or 1 gallon per 1.0 cubic feet of soil for soil treatments.

🔗 Source

When performing pre- and postconstruction applications, what is the vertical application rate?

• 0.5 gallons per 10 ft2
• 1.0 gallon per 1.0 cubic feet
• 2.0 gallons per 10 linear ft. ✓
• 4.0 gallons per 10 linear feet per foot of depth

Answer: For pre- and postconstruction applications, the vertical rate is 2.0 gallons per 10 linear ft.

🔗 Source

According to the label, how should subterranean termites in infested and/or damaged wood be treated?

• By spraying the surface of the wood with a 0.12% dilution
• By using an injection technique as described in the 'Control of Wood Infesting Insects' section ✓
• By applying 0.5 gallons per 10 ft2 to the wood surface
• By mixing 1 quart with 99.75 gallons of water and soaking the wood

Answer: The label states to treat infested/damaged wood in place using an injection technique described in the 'Control of Wood Infesting Insects' section.

🔗 Source

For pre- and postconstruction applications using a 0.12% dilution, what is permitted regarding the volume?

• The volume may be doubled if the infestation is high
• The volume of the 0.12% dilution may be reduced by 1/2 the labeled volume where desirable ✓
• The volume must be increased by 10 linear feet per foot of depth
• The volume cannot be adjusted under any circumstances

Answer: The label states that for pre- and postconstruction applications, the volume of the 0.12% dilution may be reduced by 1/2 the labeled volume where desirable.

🔗 Source

Which of the following is a stated restriction for using Bifen I T?

• Do not apply outdoors during rain
• Do not apply at a lower dosage and/or concentration than specified ✓
• Do not apply to wood without an injection technique
• Do not apply more than 2 quarts per 100 gallons

Answer: The label explicitly states: 'Do not apply at a lower dosage and/or concentration than specified'.

🔗 Source